Smart Gateway S Serial Specification

Product Name: S-Serial Smart Gateway

Model Name: DSGW-030

DSGW-030-1
DSGW-030-2
DSGW-030-3

Model list

Model

Feature

Bluetooth 5.0

Zigbee 3.0

DSGW-030-1

DSGW-030-2

Z-Wave

Wi-Fi 2.4G

DSGW-030-3

1. Introduction

1.1 Purpose& Description

 

The Smart Gateway S Serial is gateway product used in smart home, intelligent security industry, pension services. It a central device, support multiple wireless protocol including Wi-Fi and zigbee3.0,BLE, Z-WAVE. User can connect the network through Wi-Fi and Ethernet. In addition, smart sensors can be connected through zigbee3.0, BLE, Z-WAVE.

1.2 Product Feature Summary

  • OS: Linux@ OpenWrt

  • Processor: MTK7688 (MIPS24KEc(580MHZ))

  • RAM: 64MB

  • Flash: 16MB

  • Support IEEE802.11n,IEEE802.11g,IEEE 802.11b Protocol

  • Support Bluetooth 5.0

  • Support ZigBee3.0

  • Support Z-WAVE

  • One WAN/LAN variable network port

1.3 Hardware block diagram

2. Mechanical Requirement

 

2.1 Drawings

2.2 Interface

2.3 Item list

3. Specifications

 

Technical Specification

Category

​Specifications

Power Adapter

​Network Interface

Indicator LEDs

Reset Button

Operating Temperature

Input:100V~240V AC/50~60HZ Output:5V/2A, Micro USB

WLAN/LAN port

  • Power LED normally on when powered on

  • Zigbee/BLE/Z-WAVE LED is flash when the signal come

  • Wi-Fi LED normally on after connecting to Wi-Fi for 1-2 sec

The reset button is hole button, After pressing the reset button for

more than 5 seconds, the Gateway will be restored to the factory

settings.

-10℃~70℃

Performance Requirement

Wi-Fi Performance

  • IEEE wireless LAN standard:

       IEEE802.11n; IEEE802.11g; IEEE 802.11b

  • Data Rate:

        IEEE 802.11b Standard Mode:1,2,5.5,11Mbps

       IEEE 802.11g Standard Mode:6,9,12,18,24,36,48,54 Mbps

       IEEE 802.11n: MCS0~MCS7 @ HT20/ 2.4GHz band

  • Sensitivity:

        HT40 MCS7 : -70dBm@10% PER(MCS7) /2.4GHz band

        HT20 MCS7 : -71dBm@10% PER(MCS7) /2.4GHz band

  • Transmit Power:

        IEEE 802.11n: 16dBm @HT20/40 MCS7 /2.4GHz band

        IEEE 802.11g: 16dBm @54MHz

        IEEE 802.11b: 18dBm @11MHz

  • Wireless Security: WPA/WPA2, WEP, TKIP, and AES

  • Working mode : Bridge、Gateway、AP Client

  • Range: 50 meters minimum, open field

  • Transmit Power:17dBm

  • Highest Transmission Rate: 300Mbps

  • Frequency offset: +/- 50KHZ

  • Frequency Range (MHz): 2412.0~2483.5

  • Low Frequency (MHz):2400

  • High Frequency (MHz):2483.5

  • E.i.r.p (Equivalent Isotopically Radiated power) (mW)<100mW

  • Bandwidth (MHz):20MHz/40MHz

  • Modulation: BPSK/QPSK, FHSSCCK/DSSS, 64QAM/OFDM

Zigbee 3.0 Performance

  • Range: 100 meters minimum, open field

  • Transmit Power:17.5dBm

  • Highest Transmission Rate: 300Mbps

  • Frequency offset: +/- 20KHZ

  • Receiving Sensibility:-94dBm

  • Frequency Range (MHz):2401.0~2483.5

  • Low Frequency (MHz):2400

  • High Frequency (MHz):2483.5

  • E.i.r.p (Equivalent Isotopically Radiated power) (mW)<100mW

  • Bandwidth (MHz):5MHz

  • Modulation: OQPSK

Z-WAVE Performance

  • TX power: TX power up to 13dBm

  • RX sensitivity: @100kbps -97.5dBm

  • Range: 100 meters minimum, open filed

  • Frequency: 779 - 956 MHz

Bluetooth Performance

  • Bluetooth Protocol: Bluetooth 5.0​

  • TX Power: 19.5dBm

  • Range: 150 meters minimum, open filed

  • Receiving Sensibility: -80dBm@0.1%BER

  • Frequency offset: +/-20KHZ

Ethernet

  • ​10/100Mbps​​

RF Factory Test Mode

  • Setting the Board into the test mode, using the Iqexl-ws that can test the Wi-Fi, Zigbee.

  • Please refer to the DUSUN Test Specification for

4. QA Requirements

 

4.1 Quality Information

Quality &Testing Information

Information Description

Standard(Yes) custom(No)

ESD Testing

RF Antenna Analysis

Environmental Testing

Reliability Testing

Operate temperature

Certification

Yes

Yes

Yes

Yes

FCC, CE, Zigbee, Bluetooth(BQB), RoHs

-5℃~65℃

5. Software requirement

 

This software will be based on MTK platform. It run on OpenWrt system.

Features:

  • Wi-Fi

  • Zigbee3.0

  • OTA

  • MQTT

5.1 Defines

5.1.1 Boot up

When insert the power , The green and yellow Led are lighting, the Yellow LED is go out and the green LED is

blink, the green led is lighting, the gateway boot up successfully.

5.1.2 Reset

​

Keep pressing the button for 5s. All matching information is eliminated.

5.1.3 Indicator LED

​

  • Green LED: it’s used to indicate system startup

  • Yellow LED: it’s used to indicate the operating the Zigbee and z-wave. When the gateway communicate with

        sensor, the led will be blink. If let the gateway go into pairing mode, the led will be blink.

  • Red LED: it’s used to indicate gateway connect with cloud, if the gateway connect with successfully, the Red

        LED is go out, failed is lighting.

5.2 Wi-Fi Configuration

The Wi-Fi support the AP mode and client mode. It can be switched.

The name of AP: xxxxxxx

Pass word: xxxxxxx

5.3 Zigbee Configuration

The ZigBee stack is version 3.0, it can support ZHA, Greenpower, ZLL,etc. It support most cluster of ZigBee

devices.

Like door sensor, leakage sensor, Motion sensor, Tem&Hum sensor, smart plug, Smart lamp, smoke sensor,

curtain etc.

It can used web or command to add the device.

5.4 OTA

The gateway can be upgradeable over the network.

5.5 MQTT

The gateway supports the MQTT protocol to connect the cloud.

6. Application

 

1) Smart Gateway collects information about Beacon nearby, including RSSI, MAC, etc., once per second.

2) Smart Gateway send the Beacon information to Cloud via Wi-Fi .

3) Smart Gateway support the TCP/IP, UDP protocol, and can support the MQTT, LWM2M protocol.

4) Smart Gateway support connect ZigBee and z-wave devices.