Dusun wireless 4G IoT gateway available for the AT&T LTE-M network

Dusun IoT company has developed a 4G LTE IoT gateway which supports AT&T LTE-M mobile network to connect clouds. This article will discuss what is LTE-M /NB-IoT and how to use AT&T LTE-M service on Dusun IoT gateway.
Table of Contents

Dusun IoT company has developed a 4G LTE gateway which supports AT&T LTE-M mobile network to connect clouds. This article will discuss what is LTE-M /NB-IoT and how to use AT&T LTE-M service on Dusun IoT gateway.

Internet of things(IoT) has been developed for about two decades. IoT evolved from the convergence of microelectromechanical systems, micro-services, wireless technologies, and the internet. The IoT system includes IoT edge devices, IoT Gateway, and IoT cloud platform.

Connecting IoT devices to the cloud is the responsibility of an IoT gateway. In many applications, wireless communication must be used to connect the gateway to the internet. Then cellular communication can be a good choice for many IoT scenarios. Today 4G LTE network is very popular, and the 3GPP organization has published LTE CatM1, NB-IoT standards to support IoT. AT&T officially turned on its CatM1 and narrowband internet of things (NB-IoT) network after completing upgrades to its 4G LTE cell sites across the USA.

Dusun IoT company has developed a 4G LTE IoT gateway which supports AT&T LTE-M mobile network to connect clouds. This article will discuss what is LTE-M /NB-IoT and how to use AT&T LTE-M service on Dusun IoT gateway.

1. Introduction to LTE-M&NB-IoT

3rd Generation Partnership Project(3GPP)Release 13 standard defines two low-power wide-area (LPWA) technologies—LTE cat M1 and Narrow Band-Internet of Things (NB-IoT). LTE-M and NB-IoT are specifically designed for IoT.

LTE Cat M1 uplink and downlink speeds can reach 375 kb/s in half-duplex mode, and specifically supports IoT applications with low to medium data rate needs. It enables longer battery lifecycles and greater in-building range, as compared to standard cellular technologies LTE Cat 1. The main features of LTE-M include:

  • Low power consumption
  • Extended in-building range
  • Full mobility and in-vehicle handover
  • Support voice functionality via VoLTE

 

NB-IoT is low energy and low bandwidth version of IoT which is designed for the massive machine-to-machine communications. NB-IoT uses a subset of the LTE standard but limits the bandwidth to a single narrow-band of 200kHz. It uses OFDM modulation for downlink communication and SC-FDMA for uplink communications.

In LTE Release 13 and 14, 180 kHz has been proposed as the operating bandwidth for NB-IoT. NB-IoT focuses specifically on low cost, long battery life, indoor coverage, and high connection density. NB-IoT significantly improves the power consumption of user devices, system capacity, and spectrum efficiency, especially in deep coverage. The battery life of more than 10 years can be supported by a wide range of use cases.

NB-IoT is optimized for stationary use cases with little data requirements like on-off switches, smart agriculture, smart home sensors, smoke detectors, door locks, and industrial monitors. So NB-IoT is suitable for agriculture, manufacturing, healthcare, and resource management areas. LTE-M, with its greater bandwidth, can also support firmware and software updates, mobility and voice-over services.

2. Connecting Dusun Gateway to AT&T Mobile Network

Dusun 4G Gateways supports using AT&T LTE-M sim-card to connect to cloud. Users should buy a AT&T LTE-M Sim-card and activate it through the AT&T website services. Then please follow the below steps to connect the gateway with the AT&T mobile network.

1) Please insert the sim-card into the Dusun 4G gateway sim-card slot:

ATT LTE gateway
2) Power up the gateway and configure the gateway APN settings. First Log into the gateway and then revise the APN settings. Input broadband in the Apn set textbox. Please check with AT&T about the APN setting for updated information.
authorization required 1
4G 3G argments config
3) Unplug the network cable and the 4G module will startup. If the gateway can connect to a cloud platform (Dusun or others), the gateway network indicator will go out.

3. Further Info

Dusun 4G LTE IoT gateway can also support other carriers’ LTE or LTE-M services. Besides, it supports popular IoT protocols for wireless connectivity types including ZigBee 1.2/3.0, BLE, Z-Wave etc. The Gateways are built on OpenWrt system and programmable. Users can use the SDKs and APIs to write their own programs to control the data flow and processing. So this gateway can be applied in many IoT applications especially where without wired internet connections.

Further information can be found on https://www.dusuniot.com/gateways.

Related IoT Product Specifications

WSCMQ-1.2 Smart Curtain Motor

1. Product Description 1.1. Purpose and Description The Smart Curtain Motor is a versatile and convenient solution designed to enhance comfort in various settings, including

Looking For An IoT Device Supplier For Your Projects?

CONTACT US

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    IoT Gateways for Recommendation

    CONTACT US

      This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

      Welcome to DusunIoT

      Hi there 👋 Is there anything we can help you with today? Please fill in the form below for the team to follow up if you become disconnected.

        DusunIoT Distributor Program

          This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

            This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.